Hello Community,
I am actually trying to run the "QT Demo on SoCrates"
from rocketboards.org/foswiki/view/Projects/QtDemoOnSoCrates .
I have a SoCrates Board 1.2 and 2.1 and Ubuntu 14 32Bit on VMware. SoC EDS, Quartus and DS-5 are on the Windows 7 Host installed.
The OS from the socrates-training run fine.
At first I install the ELDK 5.3 with the following Components:
- denx.de/pub/eldk/5.3/install.sh
- …/5.3//targets/armv7a-hf /core-image-qte-sdk-generic-armv7a-hf.tar.gz
- …/5.3//targets/armv7a-hf /eldk-eglibc-i686-arm-toolchain-qte-5.5.3.sh
- …/5.3//targets/armv7a-hf /target.conf
After that I install the component with the following command:
./install.sh -s qte -r qte-sdk armv7a-hf
Than the eldk-switch…
and eldk-switch -r 5.3 armv7a-hf
Finally I make the makeproces with the command:
make socfpga_socrates_defconfig
make -j2 LOADADDR=0x8000 uImage
make socfpga_cyclone5_socrates.dtb
and load this files with the socrates-training mk-sd-card. sh file in a 8GB SD Card.
The U-Boot, m-preloader and the enviromentvariables are the orginal from the socrates-training directory.
I recieve at Putty the following text.
U-Boot SPL 2013.01.01 (Aug 04 2015 - 21:24:12)
BOARD: EBV SoCrates
CLOCK: EOSC1 clock 25000 KHz
CLOCK: EOSC2 clock 25000 KHz
CLOCK: F2S_SDR_REF clock 0 KHz
CLOCK: F2S_PER_REF clock 0 KHz
CLOCK: MPU clock 800 MHz
CLOCK: DDR clock 333 MHz
CLOCK: UART clock 100000 KHz
CLOCK: MMC clock 50000 KHz
CLOCK: QSPI clock 400000 KHz
RESET: COLD
INFO : Watchdog enabled
SDRAM: Initializing MMR registers
SDRAM: Calibrating PHY
SEQ.C: Preparing to start memory calibration
SEQ.C: CALIBRATION PASSED
SDRAM: 1024 MiB
ALTERA DWMMC: 0
U-Boot 2013.01.01 (Aug 04 2015 - 21:24:38)
CPU : Altera SOCFPGA Platform
BOARD: EBV SoCrates
I2C: ready
DRAM: 1 GiB
MMC: ALTERA DWMMC: 0
In: serial
Out: serial
Err: serial
Net: mii0
Hit any key to stop autoboot: 0
3761160 bytes read in 242 ms (14.8 MiB/s)
20485 bytes read in 45 ms (444.3 KiB/s)
Booting kernel from Legacy Image at 10000000 …
Image Name: Linux-3.14.0-00318-g775a3df-dirt
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3761096 Bytes = 3.6 MiB
Load Address: 00008000
Entry Point: 00008000
Flattened Device Tree blob at 00f00000
Booting using the fdt blob at 0x00f00000
Loading Kernel Image … OK
OK
Loading Device Tree to 03ff7000, end 03fff004 … OK
Starting kernel …
Nothing ist recieving more…
If I only change the uImage. That means the U-Boot, m-preloader, enviromentvariables and the socfpga_socrates. dtb are from the original socrates-training Directory, I get the following output
If I only change the uImage. That means the U-Boot, m-preloader, enviromentvariables and the socfpga_socrates. dtb are from the original “socrates-training” Directory, I get the following output
U-Boot 2013.01.01 (Aug 04 2015 - 21:24:38)
CPU : Altera SOCFPGA Platform
BOARD: EBV SoCrates
I2C: ready
DRAM: 1 GiB
MMC: ALTERA DWMMC: 0
In: serial
Out: serial
Err: serial
Net: mii0
Hit any key to stop autoboot: 0
3761160 bytes read in 246 ms (14.6 MiB/s)
20174 bytes read in 48 ms (410.2 KiB/s)
Booting kernel from Legacy Image at 10000000 …
Image Name: Linux-3.14.0-00318-g775a3df-dirt
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3761096 Bytes = 3.6 MiB
Load Address: 00008000
Entry Point: 00008000
Flattened Device Tree blob at 00f00000
Booting using the fdt blob at 0x00f00000
Loading Kernel Image … OK
OK
reserving fdt memory region: addr=0 size=1000
Loading Device Tree to 03ff8000, end 03fffecd … OK
Starting kernel …
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.14.0-00318-g775a3df-dirty (bo@ubuntu) (gcc version 4.7.2 (GCC) ) #4 SMP Wed Oct 18 22:34:00 PDT 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: EBV SOCrates
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 8 pages/cpu @bf7db000 s11328 r8192 d13248 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096
[ 0.000000] Kernel command line: root=/dev/mmcblk0p2 rw rootwait console=ttyS0,115200 uio_pdrv_genirq.of_id=generic-uio mem=1024M
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1031344K/1048576K available (5619K kernel code, 266K rwdata, 1524K rodata, 379K init, 266K bss, 17232K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc0800000 - 0xff000000 (1000 MB)
[ 0.000000] lowmem : 0x80000000 - 0xc0000000 (1024 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x80702030 (7145 kB)
[ 0.000000] .init : 0x80703000 - 0x80761c40 ( 380 kB)
[ 0.000000] .data : 0x80762000 - 0x807a4a90 ( 267 kB)
[ 0.000000] .bss : 0x807a4a90 - 0x807e72a4 ( 267 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000018] sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 42949672950ns
[ 0.000327] Console: colour dummy device 80x30
[ 0.000366] Calibrating delay loop… 1594.16 BogoMIPS (lpj=7970816)
[ 0.089744] pid_max: default: 32768 minimum: 301
[ 0.089984] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090007] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.095223] CPU: Testing write buffer coherency: ok
[ 0.095278] ftrace: allocating 18816 entries in 56 pages
[ 0.128575] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.128683] Setting up static identity map for 0x5146b8 - 0x514710
[ 1.129741] CPU1: failed to come online
[ 1.129816] Brought up 1 CPUs
[ 1.129830] SMP: Total of 1 processors activated.
[ 1.129838] CPU: All CPU(s) started in SVC mode.
[ 1.130811] devtmpfs: initialized
[ 1.138815] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.140509] NET: Registered protocol family 16
[ 1.140571] fpga bridge driver
[ 1.141250] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 1.142549] L310 cache controller enabled
[ 1.142569] l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x32460000, Cache size: 512 kB
[ 1.144099] syscon ffc25000.sdr: regmap [mem 0xffc25000-0xffc25fff] registered
[ 1.144360] syscon fffef000.l2-cache: regmap [mem 0xfffef000-0xfffeffff] registered
[ 1.144785] syscon ffc25000.sdrctl: regmap [mem 0xffc25000-0xffc25fff] registered
[ 1.145163] syscon ff800000.l3regs: regmap [mem 0xff800000-0xff800fff] registered
[ 1.146391] syscon ffd08000.sysmgr: regmap [mem 0xffd08000-0xffd0bfff] registered
[ 1.146686] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 1.146695] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 1.146981] altera_hps2fpga_bridge fpgabridge.2: regmap for altr,rst-mgr lookup failed.
[ 1.146994] altera_hps2fpga_bridge fpgabridge.2: probe deferral not supported
[ 1.147101] altera_hps2fpga_bridge fpgabridge.3: regmap for altr,rst-mgr lookup failed.
[ 1.147113] altera_hps2fpga_bridge fpgabridge.3: probe deferral not supported
[ 1.147213] altera_hps2fpga_bridge fpgabridge.4: regmap for altr,rst-mgr lookup failed.
[ 1.147223] altera_hps2fpga_bridge fpgabridge.4: probe deferral not supported
[ 1.152021] bio: create slab at 0
[ 1.153981] FPGA Mangager framework driver
[ 1.154264] SCSI subsystem initialized
[ 1.154497] usbcore: registered new interface driver usbfs
[ 1.154552] usbcore: registered new interface driver hub
[ 1.154671] usbcore: registered new device driver usb
[ 1.155523] pps_core: LinuxPPS API ver. 1 registered
[ 1.155534] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti @ linux. it>
[ 1.155555] PTP clock support registered
[ 1.156272] Switched to clocksource timer1
[ 1.179907] NET: Registered protocol family 2
[ 1.180482] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.180563] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.180706] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.180801] TCP: reno registered
[ 1.180820] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.180881] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.181166] NET: Registered protocol family 1
[ 1.181582] RPC: Registered named UNIX socket transport module.
[ 1.181593] RPC: Registered udp transport module.
[ 1.181600] RPC: Registered tcp transport module.
[ 1.181606] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.181980] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 1.182039] arm-pmu arm-pmu: PMU:CTI successfully enabled for 1 cores
[ 1.182758] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.192942] NFS: Registering the id_resolver key type
[ 1.192998] Key type id_resolver registered
[ 1.193006] Key type id_legacy registered
[ 1.193042] NTFS driver 2.1.30 [Flags: R/W].
[ 1.193393] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.194006] msgmni has been set to 2014
[ 1.194521] io scheduler noop registered (default)
[ 1.197802] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.198669] ffc02000.serial0: ttyS0 at MMIO 0xffc02000 (irq = 194, base_baud = 6250000) is a 16550A
[ 1.761234] console [ttyS0] enabled
[ 1.765167] ffc03000.serial1: ttyS1 at MMIO 0xffc03000 (irq = 195, base_baud = 6250000) is a 16550A
[ 1.774697] altera_fpga_manager ff706000.fpgamgr: fpga manager [Altera FPGA Manager] registered as minor 0
[ 1.785306] brd: module loaded
[ 1.789374] cadence-qspi ff705000.spi: DMA NOT enabled
[ 1.794574] cadence-qspi ff705000.spi: master is unqueued, this is deprecated
[ 1.802217] m25p80 spi2.0: n25q256a (32768 Kbytes)
[ 1.807245] 6 ofpart partitions found on MTD device spi2.0
[ 1.812711] Creating 6 MTD partitions on “spi2.0”:
[ 1.817508] 0x000000000000-0x000000040000 : “preloader”
[ 1.823463] 0x000000040000-0x000000050000 : “env”
[ 1.828881] 0x000000050000-0x000000060000 : “fdt”
[ 1.834287] 0x000000060000-0x000000100000 : “U-Boot”
[ 1.839947] 0x0000000a0000-0x0000006a0000 : “kernel”
[ 1.845618] 0x0000006a0000-0x000002000000 : “user”
[ 1.851154] cadence-qspi ff705000.spi: Cadence QSPI controller driver
[ 1.858152] CAN device driver Interface
[ 1.862546] c_can_platform ffc00000.can: c_can_platform device registered (regs=c08de000, irq=163)
[ 1.871765] stmmaceth ff702000.ethernet: no reset control found
[ 1.877683] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 1.882714] Ring mode enabled
[ 1.885756] DMA HW capability register supported
[ 1.890277] Enhanced/Alternate descriptors
[ 1.894626] Enabled extended descriptors
[ 1.898630] RX Checksum Offload Engine supported (type 2)
[ 1.904090] TX Checksum insertion supported
[ 1.908350] Enable RX Mitigation via HW Watchdog Timer
[ 1.919479] libphy: stmmac: probed
[ 1.922875] eth0: PHY ID 03625e6a at 0 IRQ POLL (stmmac-0:00) active
[ 1.929540] dwc2 ffb40000.usb: EPs:15
[ 1.933193] dwc2 ffb40000.usb: dedicated fifos
[ 2.796446] dwc2 ffb40000.usb: DWC OTG Controller
[ 2.801159] dwc2 ffb40000.usb: new USB bus registered, assigned bus number 1
[ 2.808224] dwc2 ffb40000.usb: irq 160, io mem 0x00000000
[ 2.813789] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.820571] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.827775] usb usb1: Product: DWC OTG Controller
[ 2.832463] usb usb1: Manufacturer: Linux 3.14.0-00318-g775a3df-dirty dwc2_hsotg
[ 2.839839] usb usb1: SerialNumber: ffb40000.usb
[ 2.844932] hub 1-0:1.0: USB hub found
[ 2.848740] hub 1-0:1.0: 1 port detected
[ 2.853000] usbcore: registered new interface driver usb-storage
[ 2.859155] usbcore: registered new interface driver usbserial
[ 2.865250] mousedev: PS/2 mouse device common for all mice
[ 2.871339] rtc-m41t80 0-0068: chip found, driver version 0.05
[ 2.877658] rtc-m41t80 0-0068: rtc core: registered m41t82 as rtc0
[ 2.884203] rtc-m41t80 0-0068: HT bit was set!
[ 2.888659] rtc-m41t80 0-0068: Power Down at 2000-00-00 03:50:53
[ 2.894890] i2c /dev entries driver
[ 2.898805] Synopsys Designware Multimedia Card Interface Driver
[ 2.905109] dwmmc_socfpga ff704000.dwmmc0: No dw-mshc-ciu-div specified, assuming 1
[ 2.912764] dwmmc_socfpga ff704000.dwmmc0: platform data not available
[ 2.919296] dwmmc_socfpga: probe of ff704000.dwmmc0 failed with error -22
[ 2.926485] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.932637] usbcore: registered new interface driver usbhid
[ 2.938206] usbhid: USB HID core driver
[ 2.942175] oprofile: using arm/armv7-ca9
[ 2.946473] TCP: cubic registered
[ 2.950392] NET: Registered protocol family 10
[ 2.955824] sit: IPv6 over IPv4 tunneling driver
[ 2.961065] NET: Registered protocol family 17
[ 2.965514] NET: Registered protocol family 15
[ 2.969963] can: controller area network core (rev 20120528 abi 9)
[ 2.976178] NET: Registered protocol family 29
[ 2.980631] can: raw protocol (rev 20120528)
[ 2.984886] can: broadcast manager protocol (rev 20120528 t)
[ 2.990541] can: netlink gateway (rev 20130117) max_hops=1
[ 2.996230] 8021q: 802.1Q VLAN Support v1.8
[ 3.000474] Key type dns_resolver registered
[ 3.004840] ThumbEE CPU extension supported.
[ 3.009125] Registering SWP/SWPB emulation handler
[ 3.014839] rtc-m41t80 0-0068: hctosys: unable to read the hardware clock
[ 3.023734] Waiting for root device /dev/mmcblk0p2…
That is the last message
Has anyone any solution for this Problem ?
Thank you and best regards.
rumbe